BMW Special Tools
Please call us at 800-535-8788 for pricing and availability
This is the only all in one solution on the market and is a must have for all owners of Direct Injected BMW vehicles.
This kit includes everything
needed to remove the direct fuel injectors & replace their seals...
*
Small slide hammer that fits into
tight spaces and provides maximum removal force for removing injectors
* Injector seal installation
expansion tool which fits neatly inside the slide hammer
* Seal Compression Dies
machined directly into the handle
* Plastic storage container
for storing new seals neatly inside case
* Die cut foam provides
perfect spot for storing additional Decoupling Elements
The blue sleeve is a dial used to
expand the seal.
Damage to the seal would occur if someone tried to force the seal on
without this tool.
The unique handle has compression dies machined directly into it.
The injector gets pushed into these holes to compress the seals in three
accurate steps.
Leave the injector in step 3 for 45 seconds to ensure the seal will remain
compressed after the injector is removed.
Then quickly (under 1 minute) install the injector into the cylinder head.
No special seal removal tool is needed or required, simply take a pair of needle nose pliers and using the tip of the pliers squeeze the seal and remove it takes second and requires very little force.
Injectors, Seals, & Decoupling Elements are not included.
Spark plug socket for the N54 engine.
Oil Filter Key Size (waf) 36 mm
Applicable for Mercedes Diesel engines OM604, OM605, OM606, BMW 1 series, BMW engines M52(6 cyl), M60(8 cyl), M70(12 cyl).
This oil filter key is intended for the removal and installation of the oil filter cover when replacing the oil filter cartridge.
Crankcase vent tool.
MOST bypass tool.
Transfer Case Actuator Motor Gear
This gear is located inside the actuator motor. Manufactured using a high temp nylon carbon fiber reinforced material which is self lubricating.
Models: X3 (E83-N) - X5 (E53) 1999-2010
Parking Brake Actuator Gear Kit
This kit contains the parts to repair the parking brake actuator (34 43 6 782 755/ 34 43 2 240 757). Includes two gears, roll pin and press tool.
Models: 7 Series E65, E66, E67, E68 to 12-2011
E39 Headlight Adjuster Kit
Halogen or Xenon, this kit includes both male plastic parts that are broken in your headlight and a tool to remove the broken ball in the female side. Good for either left or right sides. Made from 20% glass filled Delrin®.
Models: 5 Series E39 Sept. 00-03
Z3 Seat Bushing Kit
If your seat bottom has movement front to back, the cause is defective seat bushings. Kit includes eight parts which is enough to fix both seats. This is a permanent repair, made using an Acetal Resin with the trade name of Delrin®. BMW offers a kit that is made with the same original rubber that is prone to fail again.
Models: Z Series 96-02
Recline Seat Gear (Green)
Used on the front passenger’s seat. If you are close to a year break it is always best to look at your old seat gear color before ordering.
Models: 1990-1993.5 (US), 1997.5-2000 (US)
Recline Seat Gear (White)
The driver's seat in the US will always have a white recline gear. For non-US vehicles, you will need to remove and look at color of OE gear before ordering. If you are close to a year break it is always best to look at your old seat gear color before ordering.
Models: Driver’s seat – all years (US), Passenger’s seat - 1993.5-1997.5 (US)br>
Seat Bottom Gear (Pink)
The seat bottom gear will always be pink on driver's and passenger's seat. This gear takes approximately five extra minutes to replace while replacing the recline gear.
Models: All years, driver and passenger seats
This tool is used to change elastic V-ribbed belts. With the new, Conti Uni-Tool Elast, you now have the correct all-purpose tool readily at hand for nearly all vehicle applications. It makes belt changes fast, easy and fail safe. The old belt can also be removed using the new tool.
For video of this tool in action, click
on this link
http://www.crpautomotive.com/CONTIBELTS/UNITOOL/
Magnehelic Pressure Gauge 0-25 millibars
Magnehelic Pressure Gauge 0-50 millibars
Specifications are the same as 2000-25MBAR.
